Window Systems from Senior Architectural Systems

Curtain wall is designed to resist air and water infiltration and to provide a thermal barrier between inside and out.

It also allows for the filtration of more natural light into the building and is used on numerous new-build and refurbishment developments.We offer a full range of curtain wall systems that are fully drained and have a high thermal performance to cope with the most extreme weather conditions.

We can provide an extensive range of high performance curtain walling systems from ground floor treatments to high rise multi-storey facades to roof glazing, manufactured using either capped or capless systems.

A variety of mullion and transom depths allow for the fabrication of screens with large uninterrupted glazing areas creating consistent attractive facades.

All curtain wall sections are thermally broken and there are options for single, double or triple glazing. The entire curtain wall range can be supplied in a range of polyester powder or anodised finishes.

A dual colour option is available throughout. For more information regarding our products or advice on product selection, please contact our offices.

SENIOR ARCHITECTURAL SYSTEMS

SPW300

The SPW300 Window is a thermally broken polyamide aluminium window system that achieves good thermal U-values. It has a slim sightline, a wide variety of window styles and is available single or dual colour.

Open Out Casement

The SPW300 casement window has been designed to meet current building regulations. This is a 51mm thermally broken polyamide window system that achieves good thermal U-values. It is capable of accepting a variety of glazing.

All aluminium sections are extruded using Aluminium Alloy 6060 or 6063 T6 to BS EN 755 part 9 2008. Polyamide thermal barriers are manufactured in accordance with PA66 GF25. Gaskets are manufactured in accordance with BS3734.

SPW300 casement windows sections are available typically
in 3 finishes.

• Polyester Powder Coating to BS EN 12206: 2004 Part 1 –
painted in house in single or dual colour and surface finish
at 40 microns standard, or enhanced to 60 microns for
marine environments, in accordance with ISO9001,
ISO14001 and ISO18001.
• Anodised and Anolok finishes are to BS3897: 1991 to a
minimum of 25 microns (AA25), supplied in either satin or
polished finish in a limited range of colours.
• Mill finish.

SPW300 is constructed using mitred corners, joined with crimped or mechanical cleats; alignment chevrons assist in clean, accurate mitres. Integral transoms and mullions are
scribed around the outer frames and fixed with either screw ports or shear blocks. A proprietary sealant is used on all metal joints in line with good practice. Opening window
frames are designed to be inserted into the outer frames using butt hinges or friction stays.

Inward Tilt & Turn
The SPW300 tilt/turn window has been designed to meet current building regulations. This is a 51mm thermally broken polyamide window system that achieves good thermal. U-values. It is capable of accepting a variety of glazing.

All aluminium sections are extruded using Aluminium Alloy 6060 or 6063 T6 to BS EN 755 part 9 2008. Polyamide thermal barriers are manufactured in accordance with PA66 GF25. Gaskets are manufactured in accordance with BS3734.

SPW300 tilt/turn windows sections are available typically in 3 finishes.

• Polyester Powder Coating to BS EN 12206: 2004 Part 1 – painted in house in single or dual colour and surface finish at 40 microns standard, or enhanced to 60 microns for
marine environments, in accordance with ISO9001, ISO14001 and ISO18001.
• Anodised and Anolok finishes are to BS3897: 1991 to a minimum of 25 microns (AA25), supplied in either satin or polished finish in a limited range of colours.
• Mill finish.

SPW300 is constructed using mitred corners, joined with crimped or mechanical cleats; alignment chevrons assist in clean, accurate mitres. Integral transoms and mullions are scribed around the outer frames and fixed with either screw ports or shear blocks. A proprietary sealant is used on all metal joints in line with good practice. Opening window frames are designed to be inserted into outer frames using specialist gearing

Overswing
The SPW300 overswing window has been designed to meet current building regulations. This is a 51mm thermally broken
polyamide window system that achieves good thermal U-values. It is capable of accepting a variety of glazing.

All aluminium sections are extruded using Aluminium Alloy 6060 or 6063 T6 to BS EN 755 part 9 2008. Polyamide thermal barriers are manufactured in accordance with PA66 GF25. Gaskets are manufactured in accordance with BS3734.

SPW300 overswing windows sections are available typically
in 3 finishes.
• Polyester Powder Coating to BS EN 12206: 2004 Part 1 –
painted in house in single or dual colour and surface finish
at 40 microns standard, or enhanced to 60 microns for marine environments, in accordance with ISO9001, ISO14001 and ISO18001.

• Anodised and Anolok finishes are to BS3897: 1991 to a minimum of 25 microns (AA25), supplied in either satin or polished finish in a limited range of colours.
• Mill finish.

SPW300 is constructed using mitred corners, joined with crimped or mechanical cleats; alignment chevrons assist in clean, accurate mitres. Integral transoms and mullions are
scribed around the outer frames and fixed with either screw ports or shear blocks. A proprietary sealant is used on all
metal joints in line with good practice. Opening window frames are designed to be inserted into outer frames using specialist stays.

Pivot
The SPW300 pivot window has been designed to meet current building regulations. It is a 51mm thermally broken polyamide window system that achieves good thermal performance. It is capable of accepting a variety of glazing.

All aluminium sections are extruded using Aluminium Alloy 6060 or 6063 T6 to BS EN 755 part 9 2008. Polyamide thermal barriers are manufactured in accordance with PA66 GF25. Gaskets are manufactured in accordance with BS3734.

SPW300 pivot windows sections are available typically in 3 finishes.

• Polyester Powder Coating to BS EN 12206: 2004 Part 1 – painted in house in single or dual colour and surface finish at 40 microns standard, or enhanced to 60 microns for
marine environments, in accordance with ISO9001, ISO14001 and ISO18001.
• Anodised and Anolok finishes are to BS3897: 1991 to a minimum of 25 microns (AA25), supplied in either satin or polished finish in a limited range of colours.
• Mill finish.

SPW300 is constructed using mitred corners, joined with crimped or mechanical cleats; alignment chevrons assist in clean, accurate mitres. Integral transoms and mullions are
scribed around the outer frames and fixed with either screw ports or shear blocks. A proprietary sealant is used on all metal joints in line with good practice. Opening window
frames are designed to be inserted into outer frames using specialist pivots.

SPW300

SPW600

SPW600 is a three chamber, 75mm polyamide thermally broken aluminium window system offering versatility (wide variety of window styles) and is available in single or dual colour.

The SPW600e system is an evolution of SPW600 and has been further improved by the introduction of polystyrene and backer rod inserts. A wide range of sections and ironmongery allows the window system to be versatile and used in a wide range of applications.

Open Out Casement

The SPW600 and SPW600e casement window has been designed to meet current building regulations. This is a three chamber 75mm polyamide window system that achieves impressive thermal performance. It is capable of accepting glazing up to 56mm thick depending on weight.

All aluminium sections are extruded using Aluminium Alloy 6060 or 6063 T6 to BS EN 755 part 9 2008. Polyamide thermal barriers are manufactured in accordance with PA66 GF25. Gaskets are manufactured in accordance with BS3734.

SPW600 and SPW600e casement windows sections are available typically in 3 finishes.

• Polyester Powder Coating to BS EN 12206: 2004 Part 1 – painted in house in single or dual colour and surface finish at 40 microns standard, or enhanced to 60 microns for marine environments, in accordance with ISO9001, ISO14001 and ISO18001.
• Anodised and Anolok finishes are to BS3897: 1991 to a minimum of 25 microns (AA25), supplied in either satin or polished finish in a limited range of colours.
• Mill finish.

Both SPW600 and SPW600e are constructed using mitred corners, joined with crimped or mechanical cleats; alignment chevrons assist in clean, accurate mitres. Integral transoms and mullions are scribed around the outer frames and fixed with either screw ports or shear blocks. A proprietary sealant is used on all metal joints in line with good practice.

 

Inward Tilt & Turn
All aluminium sections are extruded using Aluminium Alloy 6060 or 6063 T6 to BS EN 755 part 9 2008. Polyamide thermal barriers are manufactured in accordance
with PA66 GF25. Gaskets are manufactured in accordance with BS3734.

SPW600 and SPW600e tilt / turn window sections are available typically in 3 finishes.

• Polyester Powder Coating to BS EN 12206: 2004 Part 1 –
painted in house in single or dual colour and surface finish at 40 microns standard, or enhanced to 60 microns for marine environments, in accordance with ISO9001,
ISO14001 and ISO18001.
• Anodised and Anolok finishes are to BS3897: 1991 to a
minimum of 25 microns (AA25), supplied in either satin or
polished finish in a limited range of colours.
• Mill finish.

Both SPW600 and SPW600e are constructed using mitred corners, joined with crimped or mechanical cleats; alignment chevrons assist in clean, accurate mitres. Integral transoms
and mullions are scribed around the outer frames and fixed with either screw ports or shear blocks. A proprietary sealant is used on all metal joints in line with good practice. Opening window frames are designed to be inserted into outer frames using butt hinges or tilt and turn mechanism.

Overswing
All aluminium sections are extruded using Aluminium Alloy 6060 or 6063 T6 to BS EN 755 part 9 2008. Polyamide thermal barriers are manufactured in accordance
with PA66 GF25. Gaskets are manufactured in accordance with BS3734.

SPW600 and SPW600e overswing window sections are available typically in 3 finishes.

• Polyester Powder Coating to BS EN 12206: 2004 Part 1 –
painted in house in single or dual colour and surface finish
at 40 microns standard, or enhanced to 60 microns for
marine environments, in accordance with ISO9001,
ISO14001 and ISO18001.
• Anodised and Anolok finishes are to BS3897: 1991 to a minimum of 25 microns (AA25), supplied in either satin or polished finish in a limited range of colours.
• Mill finish.

Both SPW600 and SPW600e are constructed using mitred corners, joined with crimped or mechanical cleats; alignment chevrons assist in clean, accurate mitres. Integral transoms
and mullions are scribed around the outer frames and fixed with either screw ports or shear blocks. A proprietary sealant
is used on all metal joints in line with good practice. Opening window frames are designed to be inserted into outer frames using specialist stays.

Lift & Slide

SPW600

Ali VU

SPW600 is a three chamber, 75mm polyamide thermally broken aluminium window system offering versatility (wide variety of window styles) and is available in single or dual colour.

The SPW600e system is an evolution of SPW600 and has been further improved by the introduction of polystyrene and backer rod inserts. A wide range of sections and ironmongery allows the window system to be versatile and used in a wide range of applications.

Casement Windows

The Ali VU casement window has been designed to meet current and future building regulations, with impressive U values and thermal performances. Ali VU is an evolved generation of aluminium window and door systems manufactured in the UK. It combines the long life and low maintenance of powder coated aluminium externally with a polyamide high performance thermal barrier. Ali VU casement windows are capable of accepting glazing up to 44mm thick with other thicknesses available upon request.

All aluminium sections are extruded using Aluminium Alloy 6060 or 6063 T6 to BS EN 755 part 9 2008 or BS EN 12020-2. Polyamide thermal barriers are manufactured in accordance with PA66 GF25. Gaskets are manufactured in accordance with BS3734.

Ali VU casement window sections are available typically in two finishes.

• Polyester Powder Coating to BS EN 12206-1: 2004 Part 1 – painted in house. Surface finish at 40 microns standard, or enhanced to 60 microns for marine environments, in accordance with ISO 9001, ISO 14001 and ISO 18001.

• Anodised finishes are to BS3897:1991 to a minimum of 25 microns (AA25), supplied in either satin or polished finish in a limited range of colours.

Ali VU is constructed using mitred corners, joined with crimped cleats; alignment chevrons assist in clean, accurate mitres. Integral transoms and mullions are scribed around the outer frames and fixed with either screwports or shearblocks. A proprietary sealant is used on all metal joints in line with good practice. Opening window frames are designed to be inserted directly into the outer frames using friction stays

Ali VU

PURe®

The PURe® window range is a revolutionary new range of aluminium windows which uses an innovative, enhanced thermal barrier manufactured from expanded polyurethane (PUR) allowing ultra-low U-values to be achieved.

PURe® aluminium windows are fully compatible with Senior doors and curtain walling and are available pre-finished in an almost unlimited range of colours and finishes both inside and out.

With a generic Green Guide rating of ‘A’ for use in commercial projects and a life expectancy in excess of 40 years, the PURe® window range is 100% recyclable and has been designed to meet the Passivhaus standard.

Casement Windows

The PURe® casement window has been designed to meet current
and future building regulation, with impressive U values and thermal performances. PURe® is an evolved generation of aluminium window systems manufactured in the UK. It combines the long life and low maintenance of aluminium externally with a patented high insulation PUR foam thermal barrier. PURe® casement windows are capable of accepting glazing up to 50mm thick depending on weight.

All aluminium sections are extruded using Aluminium Alloy 6060 or 6063 T6 to BS EN 755 part 9 2008 or BS EN 12020-2. Polyamide thermal barriers are manufactured in accordance with PA66 GF25. Gaskets are manufactured in accordance with BS3734.

PURe® casement window sections are available typically in two finishes.

• Polyester Powder Coating to BS EN 12206-1: 2004 Part 1 – painted in house. Surface finish at 40 microns standard, or enhanced to 60 microns for marine environments, in accordance with ISO 9001, ISO 14001 and ISO 18001.

• Anodised finishes are to BS3897:1991 to a minimum of 25 microns (AA25), supplied in either satin or polished finish in a limited range of colours.

PURe® is constructed using mitred corners, joined with crimped or mechanical cleats; alignment chevrons assist in clean, accurate mitres. Integral transoms and mullions are scribed around the outer frames and fixed with either screw ports or shear blocks. A proprietary sealant is used on all metal joints in line with good practice. Opening window frames are designed to be inserted directly into the outer frames using friction stays

Inward Tilt & Turn

The PURe® tilt and turn window has been designed to meet current and future building regulation, with impressive U values and thermal performances. PURe® is an evolved generation of aluminium window systems manufactured in the UK. It combines the long life and low maintenance of aluminium externally with a patented high insulation PUR foam thermal barrier. PURe® tilt and turn windows are capable of accepting glazing up to 50mm thick depending on weight.

All aluminium sections are extruded using Aluminium Alloy 6060 or 6063 T6 to BS EN 755 part 9 2008 or BS EN 12020-2. Polyamide thermal barriers are manufactured in accordance with PA66 GF25. Gaskets are manufactured in accordance with BS3734. 

PURe® tilt and turn window sections are available typically in two finishes.

• Polyester Powder Coating to BS EN 12206-1: 2004 Part 1 – painted in house. Surface finish at 40 microns standard, or enhanced to 60 microns for marine environments, in accordance with ISO 9001, ISO 14001 and ISO 18001.

• Anodised finishes are to BS3897:1991 to a minimum of 25 microns (AA25), supplied in either satin or polished finish in a limited range of colours.

PURe® is constructed using mitred corners, joined with crimped or mechanical cleats; alignment chevrons assist in clean, accurate mitres. Integral transoms and mullions are scribed around the outer frames and fixed with either screw ports or shear blocks. A proprietary sealant is used on all metal joints in line with good practice. Opening window frames are designed to be inserted directly into the outer frames using butt hinges or tilt/turn mechanism.

Overswing

The PURe® overswing window has been designed to meet current and future building regulation, with impressive U values and thermal performances. PURe® is an evolved generation of aluminium window systems manufactured in the UK. It combines the long life and low maintenance of aluminium externally with a patented high insulation PUR foam thermal barrier. PURe® overswing windows are capable of accepting glazing up to 50mm thick depending on weight.

All aluminium sections are extruded using Aluminium Alloy 6060 or 6063 T6 to BS EN 755 part 9 2008 or BS EN 12020-2.  Polyamide thermal barriers are manufactured in accordance with PA66 GF25. Gaskets are manufactured in accordance with BS3734. 

PURe® overswing window sections are available typically in two finishes.

• Polyester Powder Coating to BS EN 12206-1: 2004 Part 1 – painted in house. Surface finish at 40 microns standard, or enhanced to 60 microns for marine environments, in accordance with ISO 9001, ISO 14001 and ISO 18001.
• Anodised finishes are to BS3897:1991 to a minimum of 25 microns (AA25), supplied in either satin or polished finish in a limited range of colours.

PURe® is constructed using mitred corners, joined with crimped cleats; alignment chevrons assist in clean, accurate mitres. Integral transoms and mullions are scribed around the outer frames and fixed with either screw ports or shear blocks. A proprietary sealant is used on all metal joints in line with good practice. Opening window frames are designed to be inserted directly into the outer frames using butt hinges or tilt/turn mechanism.

Parallel Push

The PURe® parallel window has been designed to meet current and future building regulations, with impressive U values and thermal performances. PURe® is an evolved generation of aluminium window systems manufactured in the UK. It combines the long life and low maintenance of aluminium externally with a patented high insulation PUR foam thermal barrier. PURe® parallel windows are capable of accepting glazing up to 57mm thick depending on weight.

All aluminium sections are extruded using Aluminium Alloy 6060 or 6063 T6 to BS EN 755 part 9 2008 or BS EN 12020-2. Polyamide thermal barriers are manufactured in accordance with PA66 GF25. Gaskets are manufactured in accordance with BS3734.

PURe® parallel window sections are available typically in two finishes.

• Polyester Powder Coating to BS EN 12206-1: 2004 Part 1 – painted in house. Surface finish at 40 microns standard, or enhanced to 60 microns for marine environments, in accordance with ISO 9001, ISO 14001 and ISO 18001.
• Anodised finishes are to BS3897:1991 to a minimum of 25 microns (AA25), supplied in either satin or polished finish in a limited range of colours.

PURe® is constructed using mitred corners, joined with crimped cleats; alignment chevrons assist in clean, accurate mitres. Integral transoms and mullions are scribed around the outer frames and fixed with either screw ports or shear blocks. A proprietary sealant is used on all metal joints in line with good practice. Opening window frames are designed to be inserted directly into the outer frames using butt hinges or tilt/turn mechanism.

 

PURe®

SMRF

SMRF is a flush aluminium glazing solution with no framework visible on the external façade.

Casement Windows
Parallel Push

SMRF

TECHNAL

Soleil FY65

The SOLEAL FY 65 window system is high-performance and innovative, bringing a host of technical advancements and design features that will enhance your project.

The SOLEAL system uses a 65mm deep profile and common components to give architects, contractors, and fabricators the benefit of an extensive choice of construction options, combined with ease of specification and maximum efficiency in manufacturing.

The patented minimalist opening frame with slim, subtle sightlines to reduce the visible aluminium.

Open Out Casement
Tilt & Turn
Pivot
Parallel Push
Integrated Sash

FY65

Dualframe 75

Combining strength, safety, sustainability, and beauty within the Dualframe 75 window system was at the forefront of the design process. 

Dualframe 75 is suitable for refurbishment and new build projects across a wide range of building needs such as residential, educational and light commercial applications. 

Vents have been designed to accept the full depth Eurogroove to ensure compatibility with a wide range of industry-standard hardware.

Open Out Casement
Tilt & Turn
Pivot
Balcony Window

DF75

Dualframe 75

Combining strength, safety, sustainability, and beauty within the Dualframe 75 window system was at the forefront of the design process. 

Dualframe 75 is suitable for refurbishment and new build projects across a wide range of building needs such as residential, educational and light commercial applications. 

Vents have been designed to accept the full depth Eurogroove to ensure compatibility with a wide range of industry-standard hardware.

Open Out Casement
Tilt & Turn
Pivot
Balcony Window

DF75

HEUCK

TRIGON 40 Curtain Wall

Developed for the most modern demands on energy efficiency in the building envelope
Top values ​​in stability and thermal insulation
Simple processing and assembly thanks to the use of identical parts across all series
Filigree design thanks to slimmer face widths

Fully Capped

T40

TRIGON 50 Curtain Wall

Thermally insulated aluminium facade construction in mullion-transom construction for vertical, sloping, flat or polygonal facade walls. Identical profile geometry for mullions and transoms. Glass thicknesses from 4 mm to 58 mm. Different insert elements from the HUECK system are possible.

Fully Capped
Silicone Glazed

T50

TRIGON 60 Curtain Wall

Developed for the most modern demands on energy efficiency in the building envelope. Top values ​​in stability and thermal insulation. Simple processing and assembly thanks to the use of identical parts across all series. Filigree design thanks to slimmer face widths.

Fully Capped
Silicone Glazed

T60

ALUPROF

MB-60

MB-60 is a modern aluminium system intended for realisations of exterior architectural building elements requiring thermal and acoustic insulation, such as: various types of windows, doors, vestibules, display windows or spatial structures.

The system profiles have a three-chamber structure. The structural depth of the window sections is equal to 60 mm (frames) and 69 mm (casements), and for doors 60 mm and 60 mm, respectively. Such assumed depths of casement and frame sections give the effect of one surface from the exterior side after closing – in the case of the window, and the facing effect to the surfaces of casement and the frames – in the case of doors. Shape of the profiles allows achieving slender and resistant window and door structures.

Inward turn
Tilt & Turn
Integrated Sash
Pivot

MB-60

MB-70

MB-70 is a modern aluminium system intended for realizations of exterior architectural building elements requiring thermal and acoustic insulation, such as: various types of windows, doors, vestibules, display windows or spatial structures.

The system profiles have a three-chamber structure. The structural depth of the window sections is equal to 70 mm (frames) and 79 mm (casement), and for doors: 70 mm and 70 mm respectively. Such assumed depths of casement and frame sections give the effect of one surface from the exterior side after closing – in the case of the window, and the facing effect to the surface of casement and frames – in the case of doors. Shape of the profiles allows achieving slender and resistant window and door structures. In the MB-70 system, it is also possible to produce windows with the so-called “hidden casement” MB-70US and the MB-70 “Industrial”, finding its application during modernisations of post-industrial historic and monumental objects.

Open Out Casement
Tilt & Turn
Integrated Sash
Pivot

MB-70

MB-86

The new MB-86 window and door series have been designed to offer outstanding insulation properties. It meets the increasing requirements from the legislative and general market demands for the enhanced energy saving construction of new windows and doors.

Offered in three varieties ST, SI and AERO it is the first aluminium system to employ silica aerogel, the nanoporous material that has a very high proportion of free void volume compared to conventional solid materials. Its high pore volume, low solid content, and torturous path amorphous structure give rise to low values of thermal conductivity. Therefore the system features the industry leading thermal performance. In addition it also features exceptional rate of profiles inertia that allows for greater windows in size and weight.

Opening Turn
Tilt & Turn
Integrated Sash

MB-86

MB-104

The MB-104 Passive is a thermal break-equipped window & door system that provides the highest thermal insulation performance, and meets all the requirements for passive building components.

The system is used to fabricate exterior architectural development elements, e.g. various types of windows, doors, vestibules, and spatial structures, which are characterized, in addition to the excellent thermal insulation, by a very good sound insulation, water- and air tightness and high structural strength.

Opening Turn
Tilt & Turn
Integrated Sash

MB-104

CURTAIN WALL

Seniors SF52 fully capped / silicone glazed (SG) / vertical capped / horizontal capped / mullion drained / sloped

Seniors SF62 (only available mullion drained) / fully capped / silicone glazed / vertical capped / horizontal capped

Seniors SCW fully capped / sloped

Technal Geode MX52 visible grid / silicone glazed (SG) / vertical capped / horizontal capped /

Technal Spinal 62 visible grid / vertical capped / horizontal capped / flat capped

Technal Elegance 52 fully capped / vertical capped / horizontal capped

Hueck Trigon 40 fully capped

Hueck Trigon 50 fully capped / silicone glazed (SG)

Hueck Trigon 60 fully capped / silicone glazed (SG)

Aluprof MB-TT50

Aluprof MB-SR50 fully capped / BM-SR50 EFEKT (SG)

For any more information please call our offices or email us a message.

info@elistesystems.co.uk

Leamore Lane, Walsall, West Midlands. WS2 7DQ